ol' rusty

Rat Rods Rule

Help Support Rat Rods Rule:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Rollin!
 

Attachments

  • 20181012_130426.jpg
    20181012_130426.jpg
    208.8 KB · Views: 48
looks super great! [cl that motor is clean!


I ordered my mobsteels friday, what tire sizes are you running?

They are 20x11 and 20x9

But I had to reorder the rear ones because they are too tight against the body. I don't want them to rub. They are very well-made products
 
They are 20x11 and 20x9

But I had to reorder the rear ones because they are too tight against the body. I don't want them to rub. They are very well-made products


haha nice, but what TIRE sizes are you running on the 20x11 and 20x9

by the way I chose 20x9 and 20x8, with enough backspace for a good lip on both.

I have ordered mobsteels in the past and pam and adam are dynamite human beings.
 
More goodies
 

Attachments

  • 20181016_151116.jpg
    20181016_151116.jpg
    89.7 KB · Views: 19
  • 20181016_151408.jpg
    20181016_151408.jpg
    79.2 KB · Views: 17
So the cab is bolted down in the back, but the front had to be re worked due to the floor being a different year. I built a paper version last night. Not 100% happy but it should work. I will probably wrap a small 1" tall piece around the front to connect the outer side to the front piece
 

Attachments

  • 20181022_211639.jpg
    20181022_211639.jpg
    67.7 KB · Views: 28
  • 20181022_211259.jpg
    20181022_211259.jpg
    50.4 KB · Views: 27
  • 20181022_212406.jpg
    20181022_212406.jpg
    47.3 KB · Views: 25
  • 20181022_213416.jpg
    20181022_213416.jpg
    60.5 KB · Views: 27
Final product. Need to finish attaching it then add some seam sealer to keep the inside clean. I weld through primed the inside of it so it should stay rust free. It's really hard to see, but there is alot.of work in that ugly thing!!
 

Attachments

  • 20181023_211937.jpg
    20181023_211937.jpg
    89.9 KB · Views: 32
  • 20181023_212711.jpg
    20181023_212711.jpg
    83.4 KB · Views: 32
  • 20181023_212703.jpg
    20181023_212703.jpg
    71.4 KB · Views: 33
13 hrs later we have a new trans tunnel, finished body mounts, hole in the back of the cab for the drive line loop is covered and the trans has been pulled and reinstalled with the hydraulic throw out bearing! Getting closer!!
 

Attachments

  • 20181026_153416.jpg
    20181026_153416.jpg
    97.4 KB · Views: 41
  • 20181026_221530.jpg
    20181026_221530.jpg
    93.3 KB · Views: 30
  • 20181026_221424.jpg
    20181026_221424.jpg
    86.9 KB · Views: 30
  • 20181026_155350.jpg
    20181026_155350.jpg
    89.7 KB · Views: 28
  • 20181026_221542.jpg
    20181026_221542.jpg
    122.5 KB · Views: 28
Got the cab almost done. Have a few more areas along the fire wall
 

Attachments

  • 20181029_183506.jpg
    20181029_183506.jpg
    129.9 KB · Views: 17
  • 20181029_205608.jpg
    20181029_205608.jpg
    150.2 KB · Views: 13

Latest posts

Back
Top