Search results

Came out of an intersection hard on the gas, and big cloud of smoke, half block later when I pulled onto a side street, hood was filled, etc. Turns out the tranny cooler line either was rubbing, or touched the hot on the starter and burned a pin hole through it, so it was spraying tranny fluid...

the basic inexpensive router is designed to be a master, typically you can't use two routers, but the Bridge (like Toad) said can be a slave and will connect to your existing wifi and create another wifi. For Smallfoot If your shop is really out of range and is connected to the House's...

looking for a 7 degree balljoint reamer (less than $90) I need for just one cut , and thinking someone might have one that was only used once too.

not sure if the time frame is long enough but take a look at the turbo timers, ultimately they are switching a relay. The apexi 's have some really cool countdowns and are about $18.00

thanks, I went out today and after 1 gallon it was full. I was thinking maybe something got sucked onto the pickup tube and went I dumped in more gas it washed off, or I never thought of a hole in the pickup tube. guess I will run it down to make it lighter and then drop it. thanks for the...

I have a '50 Dodge truck with fuel filler on side of cab, factory pipe so maybe 2', with a 90 degree into a tanks unlimited 16 gallon tank. The question/problem was it ran out of gas early after 111 miles, but can go to 160, but I dragged a few people so did have my foot in the tank a few times...

http://www.ebay.com/itm/VINTAGE-NOS-1950s-DEK-BLONDE-CAR-CHIC-MARILYN-MONROE-AUTOMOTIVE-DASH-ORNAMENT-/221803908195?fits=Year%3A1950|Make%3ADodge|Model%3ATruck&hash=item33a48b0c63&vxp=mtr do you think this was every popular, or did they just make this one that never sold?

I dunno I see its for sale but that paint job looks kinda fake, might be a photoshop, I'd be careful if I was you.

Is there any decent gas suppliers open on a Saturday in Vancouver? KMS tools sucks, tired of no service and getting either leaky tanks or empty tanks on there exchange. Might have to start taking Friday afternoon's off to go to Air Liquide.

I'M 6'5" AT 235 the secret is bad posture, I slouch when I drive, got lots of headroom, legroom sucks a bit but had a lotta years to get used to that. I like the hunched forward, right hand on left side of big 18" wheel, right elbow on right side.

the part store usually have rebuild kits for $20 that includes gaskets, jets, etc PLUS instructions and assembly spec,s exploded view.

thanks for the responses, I have just a worm gear clamp on it. I think I will try one of the "T" clamps that are also wider, or as suggested both!

I used flex rad hose on both the upper and lower on a SBC chevy to a KMJ aluminum rad, but have had problems with the rubber and chrome parts seperating over time. Over 600 miles of driving and they either pop apart or have travel back close to coming off. Wondering if there is too much frame...

took the saturday off break in the weather allowed for a few pictures

I took two allen key t-handles and cut them short, put collars to stop movement and then welded to a short piece of flat bar. thats connected to a solid 1/4 " round stock that goes through the door and the post and pins the door closed. guess I should go take a photo but it kinda looks like a...

for straight cuts I like grinder, but for curves or circles Jigsaw. But you need to clamp it down and keep the clamp close to the cut otherwise it will bounce. Basically when you can;t focus on the steel its time to move the clamps

I got my 50' out of a field had to cut a tree out of the engine bay to move it. But probably like everyone else here I loose interest in a build if it takes too long. So I got it running, mechanical, functional, mostly safe, and started driving it. It was when I was out on the streets that I...

I've always been partial to shaved, with remote poppers.

alot of the time the signal to the ecu is 5 volts. So there is a complicated circuit to detect the correct key, but the output is probably just a 5 volt. I would open the ecu and find the pin that connects and give it 5 volts. If that works you can tie into one of the switched circuits.